Frequently asked questions
We have a table for calculating the weight of a door, which is necessary to know when choosing guy ropes and measurements.Depending on the material of the door, as well as its dimensions, the result will be the weight of the door (kg) that you can use to calculate to the necessary strength of the measure (Kg x cm).
The Vertex external drawer supports a maximum weight of 40 kg, thanks to its synchronised full-extension slide system and high-strength steel.
The board for the back and rear must be 16 mm thick to ensure proper installation.
The drawer front is adjustable up to ±2 mm vertically and ±1 mm horizontally, ensuring correct alignment.
Yes, the slide system includes a cushioned closure, which provides a smooth and quiet closure.
Kit includes: 1 set of slides, 1 set of ribs, 1 set of drawer front clips and screws. Front, back and bottom are not included and must be purchased separately.
It is compatible with 131 mm high Vertex drawers.
This rib must be installed on the left side of the drawer.
Supports a depth of 350 mm.
It is made of steel with an anthracite grey finish.
This rib provides support and stability to the drawer, remaining visible with a formal and modern design thanks to its anthracite grey finish.
In order to know if a screw is compatible with a nut or stud bolt are compatible, we have to look at the internal thread of the screw and at the thread of the nut or stud bolt, which must coincide.For example, if we choose a nut or stud boy with a 6 metric screw thread (M6), the screw also has to have an internal metric thread of 6 (M6).
We have a table for calculating the pistons or dampners, where you can obtain a response with the furniture data.The choice will depend on the width and the height of the door, as well as the material it is manufactured out of, in addition to the stroke of the piston or damper itself.The result will be the number of pistons or dampners and the necessary strength of each one.
For the same force required in both folding and lift up doors, we recommend that you only use a single piston or damper in a door with a width of less than 450 mm, and that you use two pistons or dampers for a door that is wider than 450 mm.
Yes, the luminaire is adjustable in length between 462 and 468 mm thanks to the lateral brackets, allowing it to be adapted to the width of the drawer or cabinet.
The integrated proximity sensor allows the luminaire to switch on automatically when the drawer is opened and off when the drawer is closed, improving convenience and energy savings.
No, the 500 mm cable entry profile is specifically designed to be installed at the rear of the drawer, ensuring that it does not interfere with the movement of the drawer.
The luminaire is mainly made of matt anodised aluminium and plastic, guaranteeing durability and a modern design.
The luminaire has an IP20 protection rating, making it ideal for installation in dry interior spaces such as cupboards or drawers.
The Placard trim profile is designed to provide protection for the edges of glass doors, ensuring an airtight and aesthetic seal within the Placard sliding system.
It can be easily adapted to different thicknesses of glass or boards.
It is made of high quality plastic with a grey finish, ensuring durability, flexibility and resistance to continuous use.
Installation is simple: the profile is fitted directly onto the edges of the glass door before inserting it into the sliding system. No additional tools are required.
Yes, the profile is designed to help absorb light impacts, protecting the edges of the glass door against chipping and damage.
This kit is specifically designed for 19 mm thick boards. To ensure correct operation, it is not recommended for use on thicker or thinner boards, as this may compromise the stability of the installation.
The kit includes handles and hardware for a door up to 2.7 metres in length. If a shorter door is required, the aluminium profiles can be cut to size to fit the desired size.
The kit is designed for sliding doors installed on wood or chipboard surfaces compatible with 19 mm thick boards. It is important to ensure that the surface is smooth, level and strong enough to support the weight of the door.
The kit includes 2 integrated brakes that ensure a smooth and controlled closing of the door, avoiding sudden impacts. This system improves safety and prolongs the life of both the hardware and the panel.
The slim profile design maximises visual space, achieving a modern, minimalist style, ideal for contemporary cabinets.
The handle is made of aluminium, which makes it light but strong. This makes it easy to handle and install without compromising durability.
No, this handle is specifically designed for Placard 61 sliding doors and is therefore not recommended for hinged doors.
A thin-cutting saw for aluminium and a ruler or tape measure are required to ensure precise cuts to the desired size.
The Sharp 18E handle is specifically designed for boards with a thickness of 18 mm, ensuring a perfect fit and a clean finish.
The MAW (Maximum Allowable Weight) of the Gola profile system finishes depends on their correct installation and the components used, guaranteeing stability in standard kitchen furniture.
The Gola system is installed in kitchen units with top, bottom and vertical profiles. Be sure to follow the included assembly instructions to ensure proper alignment and a clean finish.
It is recommended to leave a gap of at least 2 mm between the door and the profile to ensure a smooth opening without chafing.
To integrate appliances with the Gola system, it is important to use the appropriate vertical and horizontal profiles, ensuring that they do not interfere with the dimensions of the appliance.
The PMA (Maximum Weight Allowance) of the Gola profile system finishes ensures stability and strength in kitchen furniture designed for standard use.
The Gola Top profile is installed by fitting and requires a 3 mm pre-milling of the board to fit perfectly. The manufacturer's instructions must also be followed to ensure correct fixing.
This profile is compatible with table tops with a thickness of 18 mm, ensuring perfect integration into modern kitchen furniture.
Yes, the design of the Gola Top Profile makes it ideal for kitchens with a minimalist style, thanks to its clean finish and unobtrusive integration into the furniture.
The central Gola profile is designed to be discreetly integrated into the central part of the kitchen units, offering a clean and modern look. Its main function is to allow convenient access to drawers and doors without the need for external handles.
The central Gola profile is made of aluminium with finishes such as white painted, matt anodised or gold anodised, ensuring strength and durability.
The central Gola profile has a length of 2.35 metres, ideal for fitting a wide variety of kitchen units.
The central Gola Profile design provides a modern, linear aesthetic, eliminating the need for external handles and facilitating cleaning by reducing edges and surfaces exposed to dust.
Accessories such as brackets, end caps and brackets are fully compatible with the Central Gola Profile, making installation easy and allowing for custom configurations.
The central vertical curved Gola profile is designed for installation in handle-free kitchen fronts, especially in tall units and pantry cabinets. It provides convenient access and modern aesthetics by eliminating visible handles.
The profile has a standard length of 2.35 metres, although it can be cut to any desired length to suit the needs of the furniture.
The profile is made of high quality aluminium with a white painted finish, which guarantees durability and resistance to wear and tear.
Yes, the Gola profile can be cut to size using suitable tools, allowing it to be adapted to different furniture projects.
The packaging includes a central vertical curved Gola profile with protection against scratches or damage during transport.
The cover for Gola central profile has the function of sealing the side parts of the profile, providing an aesthetic finish and protecting it from friction or damage.
Yes, this cover is specifically designed to be compatible with all central Gola profiles used in kitchen systems.
It is made of high quality aluminium with a white painted finish, which guarantees strength and durability.
The packaging includes a closed cover for the central profile, a hexagonal spanner and two screws required for correct installation.
The lid is fixed by means of a precision mechanism that ensures a perfect fit together with the included screws, preventing displacement or misalignment.
The Gola Top profile facilitates the opening of handle-free doors, providing a modern and minimalist aesthetic.
Yes, the Gola Top profile is designed to fit 16 mm and 19 mm thick boards, ensuring its versatility.
It is made of high quality aluminium with a white painted finish, guaranteeing durability and resistance.
The Gola Top profile has a length of 2.35 metres and an elongated design with an outer overhang of 18 mm.
The packaging includes a Gola Top profile, ideal for completing the Gola system in kitchen furniture.
The Gola curved vertical side profile is designed to be integrated into handle-less kitchen fronts, optimising the opening of doors in pantry columns or cupboards.
The profile has a length of 2.35 metres and can be cut to size to suit different kitchen projects.
Yes, installation is simple, thanks to a direct anchoring method and sliders that facilitate assembly.
It is made of high quality aluminium, guaranteeing long-term durability and strength.
The Gola curved vertical side profile is available in white, black, anthracite, matt anodised, gold anodised and stainless steel anodised finishes.
The kit includes 2 x 2.35 metre Gola profiles, 2 sets of Gola accessories and 2 brackets with screws for the profiles, providing everything you need for a complete installation.
It is designed for kitchen furniture with handle-less fronts, providing a modern and functional design.
The included profiles are each 2.35 metres long and can be adapted to modules of different dimensions.
This kit facilitates assembly thanks to the included accessories and brackets, reducing installation time and guaranteeing a precise fit.
The profiles are made of high quality aluminium, which ensures strength, durability and a flawless finish.
The kit includes 2 x 2.35 metre Gola profiles, 2 sets of Gola accessories and 2 brackets with screws, providing everything you need for a complete installation.
It is suitable for kitchen furniture with handle-less fronts, providing a modern and functional design.
The included profiles have a length of 2.35 metres, ideal for fitting into standard kitchen units.
The kit facilitates assembly thanks to the included accessories, simplifying installation and guaranteeing a perfect fit.
The profiles are made of high quality aluminium, which ensures durability, strength and a flawless finish.
The Plasline 90 degree angle for Plasline skirting boards allows skirting boards to be securely and aesthetically joined at internal corners, ensuring a solid connection and a uniform visual finish.
In order to know if a nut is compatible with a leveller, we have to look at the internal thread of the nut and at the thread of the leveller, which must coincide.For example, if we choose a 4 metric screw thread (M4), the nut also has to have an internal metric thread of 4 (M4).
It is compatible with plinth heights of 100 mm, 120 mm, 150 mm and 180 mm, adapting to different kitchen configurations.
It is made of high quality plastic and anodised aluminium, ensuring strength, durability and an attractive visual finish.
No, the 90 degree angle is designed to be installed directly without the need for additional adjustments or cut-outs.
Each pack includes 20 units of 90 degree angles, ideal for kitchen skirting installation projects.
The Boston furniture handle has a total length of 170 mm, which makes it ideal for modern, elegant furniture.
It is made of Zamak, a robust material that combines durability and corrosion resistance, perfect for prolonged use.
The distance between the fixing holes of the handle is 128 mm, compatible with standard sizes in kitchen and household furniture.
The satin nickel finish provides a sophisticated, modern look and is resistant to scratches and everyday wear and tear.
Yes, the handle includes the necessary screws (M4 screws) for quick and easy installation.
For the assembly of Free Face profile hands for board of 19-20 mm alongside the Space+ sliding door system, it is necessary to choose an outside runner with a thickness of 30 mm and adhesive spacer cod. 4000820.
For the assembly ofFree Face 2 profile hands for board of 19-20 mm alongside the Space+ sliding door system, it is necessary to choose an outside runner with a thickness of 23 mm.
The Calgary handle is made of zamak, a metal material known for its durability and strength.
The handle has a total length of 166 mm and a gap of 160 mm, suitable for most furniture.
The handle is finished in satin nickel, giving it a modern and elegant look.
Yes, the handle includes M4 screws to facilitate quick and accurate installation.
The Calgary handle packaging contains 25 units, ideal for series installation projects.
For the assembly of the Free poor alongside the Space + sliding door system, it is necessary to choose an outside runner with a thickness of 30 mm.
The Denver knob is made of aluminium, a light and strong material that offers durability and aesthetics.
The knob has a diameter of 12 mm, ideal for combining with different styles of furniture.
The finish is matt anodised, providing a modern and minimalist look.
Yes, the knob includes M4 screws required for easy and secure installation.
The packaging contains 50 pieces, perfect for large or serial projects.
The handles of the Castellar range are made of steel with chrome and matt chrome finishes, which ensures high resistance and durability.
The dimensions of each handle are 104 mm long, with a 96 mm spacing, ideal for various furniture applications.
The set includes 20 handles and is available in two finishes: chrome and matt chrome, to suit different design styles.
The set includes M4 screws, suitable for quick and secure installation of the handles on furniture.
Yes, these handles can be installed in both horizontal and vertical orientation, depending on the design and need of the furniture.
The handles of the Utiel range are made of steel with a satin nickel finish, guaranteeing strength and durability.
This batch is only available in satin nickel finish, which gives it a modern and elegant design.
The dimensions of each handle are 152 mm in length and 128 mm spacing, ideal for different furniture applications.
They include M4 screws designed for fast and secure installation, with perfect fits for furniture.
Yes, the handles are designed to be installed in both horizontal and vertical orientation, depending on the need of the furniture.
The Vienna knob is made of zamak, a strong material that ensures durability and quality aesthetics.
It is available in satin nickel, satin nickel and mocha, and painted mocha, adapting to different styles of decoration.
The knob has a diameter of 20 mm and a height of 20 mm, ideal for small and decorative furniture.
Includes M4 screws designed for quick and secure installation, ensuring an optimal fit in any furniture.
The Vienna knob is ideal for drawer fronts and cupboard doors in kitchen, bathroom, home and office furniture.
Benetússer knobs are made of zamak, a resistant material that combines durability and elegant design.
Available finishes include satin nickel and mocha, ideal for matching different styles of furniture.
Each knob has a diameter of 41 mm, which makes them suitable for small and decorative furniture.
The knobs are easily installed using the screws provided. They can be recessed or surface-mounted according to the desired design.
This set of knobs is perfect for kitchen, bathroom, home and office furniture, such as drawers and cabinet doors.
The lot includes 20 Alfafar handles, each one accompanied by the necessary mounting screws, individually packaged to avoid knocks and scratches.
Although the he adjustable, visible, hanging Neco sliding system allows for a maximum door thickness of 30 mm, the fittings and profiles of the Free aluminium door do not allow for the assembly of this sliding door system.
It is ideal for kitchen, bathroom, home and office furniture and is compatible with both horizontal and vertical doors.
Installation is simple, as it is fixed with the included M4 screws, ensuring a firm and precise integration into the furniture.
The Alfafar handle is made of high quality aluminium, which guarantees lightness and resistance to corrosion.
The matt anodised finish gives it a modern aesthetic and excellent durability against daily wear and tear.
The lot includes 20 Paiporta handles and all the M4 screws necessary for their installation, individually packed to avoid knocks and scratches.
The handle is suitable for kitchen, bathroom, home and office furniture and can be installed on both horizontal and vertical doors.
Installation is carried out by fixing the handle with the M4 screws included in the package, ensuring a firm and durable hold.
The Paiporta handle is made of zamak, a robust and corrosion-resistant material, ideal for prolonged use.
It is available in various finishes, such as chrome, painted black, painted aluminium and satin nickel, to suit different styles and preferences.
The set includes 20 Bombay handles and the M4 screws required for installation. Each handle is individually packaged to avoid knocks and scratches.
The Bombay handle is suitable for kitchen, bathroom, home and office furniture, and can be installed on both horizontal and vertical doors.
The distance between the mounting holes of the handle is 128 mm, offering a standard and versatile size.
Bombay handles are made of zamak, a material resistant to corrosion and wear, guaranteeing durability.
The Bombay handle is available in painted aluminium and satin nickel finishes, adapting to different decorative styles.
The set includes 25 Albal knobs made of zamak, together with the screws required for installation. Each knob is individually packaged to avoid damage during transport.
Albal knobs have a diameter of 16 mm, which makes them ideal for small furniture or as decorative details.
Albal knobs are available in chrome and satin nickel finishes, offering options for different decorative styles.
Albal knobs are ideal for kitchen, bathroom, home and office furniture, adding a modern and functional touch.
Each knob is individually packaged, which guarantees protection against knocks and scratches during transport and storage.
The lot includes 25 handles made of aluminium with the necessary screws for their correct installation.
The Picanya handle has a length of 45 mm and an interaxis of 32 mm, making it ideal for a wide variety of furniture applications.
The handle is available in matt anodised, gloss anodised, black anodised and stainless steel anodised finishes.
Yes, the Picanya handle can be installed both horizontally and vertically, depending on the needs of the furniture design.
Each handle is individually packed to avoid knocks and scratches during transport and storage.
The Verona knob has a diameter of 25 mm, offering a compact and modern design.
It is made of aluminium with a matt anodised finish, guaranteeing durability and resistance to corrosion.
The package includes a knob and the screws necessary for correct installation.
It is suitable for kitchen, bathroom, home and office furniture, as it combines functionality and aesthetics.
Each knob is individually packed to avoid knocks and scratches during transport.
The Orlando handle is made of steel with a black painted or satin nickel finish, ensuring durability and a modern design.
The mounting hole spacing of the Orlando handle is 128 mm.
The set includes 10 handles and the M4 screws required for installation.
Yes, the Orlando handle can be installed in both horizontal and vertical orientation, adapting to different types of furniture.
Each handle is individually packed to avoid knocks and scratches during transport.
The Kobe handle is made of zamak with a high quality titanium-coloured finish, offering durability and a modern design.
The distance between the mounting points of the Kobe handle is 96 mm, which makes it compatible with most standard furniture.
The set includes 20 Kobe handles and the necessary M4 screws for their correct installation.
Yes, the titanium finish is designed to be highly resistant to corrosion, scratches and everyday wear and tear, ensuring a long service life.
Each handle is individually packaged to avoid knocks and scratches during transport, ensuring that they arrive in perfect condition.
Kyoto handles are made of zamak, a durable and resistant material, with a high quality satin nickel finish.
The distance between the fixing points is 96 mm, which makes them compatible with standard furniture.
The set includes 20 Kyoto handles and the M4 screws required for installation.
Yes, the satin nickel finish is designed to offer resistance to wear and maintain its original appearance for longer.
Each handle is individually packaged to avoid knocks and scratches during transport, ensuring that they arrive in perfect condition.
The Nagoya handle is made of zamak with satin nickel and titanium-coloured finishes, durable and high quality materials.
The distance between the fixing points is 64 mm, compatible with standard furniture.
The packaging includes 1 Nagoya handle and M4 screws required for installation.
Yes, the Nagoya handle can be installed both horizontally and vertically, adapting to the needs of the furniture design.
Each handle is individually packaged to avoid knocks and scratches, ensuring it arrives in perfect condition.
The Seoul handle is made of steel with a satin nickel finish, offering high resistance and a modern design.
The distance between the fixing points is 128 mm, suitable for standard furniture.
The packaging includes 1 Seoul handle and M4 screws required for installation.
Yes, the handle can be installed both horizontally and vertically, adapting to the design of the furniture.
Each handle is individually packed to avoid knocks and scratches during transport.
The Aldaia handle is made of zamak with satin nickel, black painted or metallic grey finish, which ensures resistance and a modern design.
The distance between the fixing points is 96 mm, a standard measurement for furniture.
The lot includes 25 Aldaia handles and M4 screws required for installation.
Yes, the handle can be installed either horizontally or vertically, depending on the desired design.
Each handle is individually packed to avoid knocks and scratches during transport.
The Shanghai handle is made of zamak, a strong material that offers durability and a high quality finish.
The distance between the fixing points is 128 mm, which is standard for this type of handle.
Yes, the Shanghai handle can be installed either horizontally or vertically, depending on the design requirements.
The packaging includes a Shanghai handle and the M4 screws required for installation.
Each handle is individually packed to avoid knocks and scratches during transport.
The Algemesí handle is made of aluminium with a matt anodised finish, which guarantees durability and a modern appearance.
The distance between the fixing points is 128 mm, a common standard for easy installation.
Yes, the Algemesí handle is designed to be installed both vertically and horizontally, depending on the needs of the design.
The lot includes 25 Algemesí handles, each accompanied by M4 screws for installation.
Each handle is individually packed to avoid scratches and knocks during transport.
The Glasgow furniture handle is made from aluminium with a matt anodised finish, ensuring strength and durability, as well as a modern and attractive design.
Yes, the Glasgow handle is designed to be installed both horizontally and vertically, adapting to different styles and needs.
The Glasgow handle has a mounting hole spacing of 64 mm, which makes it easy to install on standard furniture.
The batch of 25 Glasgow handles includes M4 screws required for installation and each handle is individually packaged to prevent knocks and scratches.
The Glasgow handle is available in various lengths: 84 mm, 148 mm and 180 mm, to suit different sizes of furniture.
The Minneapolis furniture handle is made of zamak with a satin nickel finish, giving it durability and a modern design.
The distance between the mounting holes of the Minneapolis handle is 160 mm, compatible with most standard furniture.
Yes, the design of the Minneapolis handle allows it to be installed both horizontally and vertically, adapting to different styles.
The package includes a handle and the necessary M4 screws for mounting, as well as individual packaging to protect against knocks and scratches.
This handle is ideal for kitchen, bathroom, home and office furniture, providing functionality and a decorative touch.
The Pedralba furniture handle is made of zamak with a chrome finish, guaranteeing durability and an elegant design.
The distance between the mounting holes of the Pedralba handle is 128 mm, compatible with standard furniture.
Yes, the Pedralba handle is designed to be installed both horizontally and vertically, adapting to different design needs.
The package includes a handle and the necessary M4 screws for installation, all individually packaged to protect the product.
This handle is ideal for kitchen, bathroom, home and office furniture, offering modern style and functionality.
The Santiago furniture knob is made of zamak with a satin nickel finish, offering durability and a modern design.
The package includes a knob and the necessary M4 screws for installation.
Yes, the Santiago knob is ideal for kitchen, bathroom, home and office furniture, thanks to its versatile design.
Each knob is individually packed to avoid knocks and scratches during transport.
Yes, the Santiago knob is designed for installation on both drawer fronts and cabinet doors.
The Milano furniture knob is made of zamak with a satin nickel finish, guaranteeing strength and a modern design.
The package includes a knob and the necessary M4 screws for installation.
Yes, the Milano knob is ideal for kitchen, bathroom, home and office furniture, thanks to its versatile and modern design.
Each knob is individually packed to avoid knocks and scratches during transport.
Yes, the Milano knob is designed to be installed on both drawer fronts and cabinet doors.
The Nairobi handle is made of zamak, a high quality and resistant material.
The handle has a bronze finish, ideal for rustic, classic or colonial styles.
The Nairobi handle has a length of 139 mm and a centre-to-centre distance of 96 mm.
The package includes 1 handle and the M4 screws required for installation.
Yes, each handle is individually packed to avoid knocks and scratches during transport.
The Papua handle is made of zamak with ceramic details, providing durability and an elegant design.
This handle is available in bronze and old silver finishes.
It has a length of 127 mm and an interaxle of 76 mm.
The package includes 1 handle and the M4 screws required for installation.
Yes, the Papua handle is designed to complement rustic, classic or colonial styles.
The Alberic handle is made of zamak, a strong and durable material.
This model is available in bronze and black painted finishes.
The handle has a length of 77 mm and an interaxle of 64 mm.
The package includes 1 handle and the M4 screws required for installation.
Yes, the Alberic handle is specifically designed to complement rustic, classic or colonial style furniture.
The Massanassa knob is made of zamak, a durable and resistant material.
This model is available in bronze and black painted finishes.
The diameter of the knob is 32 mm.
The package includes 1 knob and the necessary M4 screws for installation.
Yes, the design of the Massanassa knob makes it ideal for complementing classic, rustic or colonial style furniture.
Yes, it is possible to cut the 80 feet. To do so, you need to cut the foot at the leveller part, once this part has been disassembled, and make the cut with a cutting disk/saw that is suitable.
The knob has a total length of 60 mm, which makes it suitable for different types of furniture.
It is made of aluminium, which guarantees durability, strength and lightness.
The knob has a bronze finish and is individually packaged to avoid scratches during transport and storage.
Yes, the package includes M4 mounting screws, ensuring quick and easy installation.
Yes, its aluminium construction and durable finish make it ideal for use in wet environments such as kitchens and bathrooms.
The Wave 16 and Wave 16 E handle profiles for creating sliding doors have the same design and the same geometry for 16 mm thick board. The difference is that the Wave 16 E handle profile has a reduced thickness and is therefore more cost-effective.
The following diagram shows the detail of the machining that you need to carry out on the table top of a table in order to fasten the plate of the 60 - 80 feet.
The following video shows how the sliding door system for wardrobes is assembled.
The Barn system allows installation without machining inside the module, which reduces assembly times and avoids structural errors. In addition, it provides decorative and functional value when integrated as a design element, ideal for rustic, industrial or modern projects with exposed aesthetics.
Yes, for double door installations, the kit can be duplicated or a 4 metre double track can be purchased. It is important to ensure the alignment of the profiles and to leave adequate clearance between the two leaves to avoid interference during opening and closing.
It is not recommended to fix directly on plasterboard without structural reinforcement. To guarantee safety and correct operation, it is advisable to install on brick or concrete walls or to add an internal wooden frame anchored to the metal profiles of the partition.
Periodically check the tightness of bolts, ensure that the wheels do not accumulate dust or debris, and apply dry lubricant to the rotating axle if excessive noise or friction is detected. Black epoxy painted steel is highly resistant, but direct exposure to persistent moisture should be avoided.
The Barn system is designed as a free-opening solution without built-in soft closing. However, it can be combined with external damping accessories or concealed brake guides if they are correctly integrated behind the panel, adapted to the final door travel.
According to the ISO standard: 7170:2005 Emuca supports can take a maximum weight of 40 kg per metre evenly distributed.
Each Alumik X base is designed to withstand an approximate static load of up to 50 kg, depending on the weight distribution at the base of the unit. They are ideal for kitchen and bathroom base units or auxiliary furniture for domestic or low-demand commercial use.
Yes, they are made of high-strength ABS plastic and have a painted or chrome-plated finish to protect against environmental humidity. Their use is especially recommended for furniture exposed to the floor, such as kitchens and bathrooms.
No. Each foot includes fixing screws and its base is designed for direct installation with conventional screwing. The flat support surface and alignment of the holes facilitates mounting with standard tools, without the need for special jigs.
The height of each Alumik X foot is fixed, 80 mm from the base to the point of contact with the furniture. It is not a height-adjustable model, so it is recommended for use in level modules or with flat bases.
The Alumik X design not only enhances the aesthetics of the cabinet with a modern profile, but also offers greater structural stability thanks to its wide base. This shape also facilitates ventilation underneath the cabinet and allows for better weight distribution.
It is specifically designed for structures with metal plinth or modules that require adjustment from the inside of the side, such as kitchen units, technical cabinets or bathroom furniture with uneven floors. It is ideal for applications that require a robust and discreet fixing.
For assembly, an Allen key no. 4 is required to adjust the M10 leveller from inside the module. The bracket is screwed directly to the side of the cabinet with standard screws (not included), allowing a height adjustment of up to 25 mm.
The set has a sturdy metal bracket and a leveller made of steel and technical plastic. In standard applications, each unit supports up to 60 kg distributed, being suitable for furniture up to 250 kg if 4 units are used correctly fixed.
The system allows a height adjustment of 25 mm. The travel is designed to absorb uneven floors or compensate for differences between modules without compromising stability, with a minimum height of 46 mm and a maximum height of 71 mm.
This model incorporates a metal bracket that improves lateral support, especially useful in furniture that is installed in series or that requires frequent disassembly. In addition, its concealed plastic cover improves aesthetics and prevents dirt from entering the mechanism.
The Bowl castor with mounting plate is fastened with screws in the preformed holes in the top plate (zinc-plated steel). We recommend using Ø4 mm flat-head or countersunk screws with a minimum length of 16 mm, suitable for the furniture material (melamine, MDF or chipboard).
The ball bearing allows a much smoother and quieter movement, ideal for light everyday furniture. This system improves the durability of the assembly and reduces wear and tear on delicate floors such as laminate or parquet.
Yes, provided that the surface is suitable for fastening with screws. For extruded aluminium profiles, the use of self-drilling screws or rivet nuts type M4 is recommended to ensure a firm and durable fastening.
The recommended load per castor is 50 kg. On furniture with four correctly installed castors, a total load of up to 200 kg can be distributed, provided that the weight is evenly distributed and the surface is stable.
For optimum performance, it is advisable to periodically check the condition of the ball bearing and remove accumulated dust or debris. In high humidity or dusty environments, applying a small amount of dry lubricant can prolong service life.
The following video shows how the sliding door system for wardrobes is assembled.
The following video shows how you can easily assemble the Vertex drawer.
According to the number of doors that comprise your wardrobe you can choose between different types of Free aluminium vertical profiles (A, B or C) to obtain different combinations of doors.
Type A. Central door used to create wardrobes with three doors. Created with two handle profiles.
Type B. Outer door used to create wardrobes with two or four doors. Created with a handle profile and a handle cover profile.
Type C. Inside door used to create wardrobes with two or four doors. Created with a vertical profile and a handle profile.
The following video shows how you can easily to adjust the Vertex drawer.
The bumper is designed to fit into a 5 mm diameter hole, ensuring a precise and secure fit on wooden boards or similar.
Can be installed in wood, MDF, chipboard or other soft materials where a clean 5 mm hole can be drilled without damaging the internal structure.
The T-shaped design ensures a larger contact surface when closing doors or drawers, offering better impact absorption and reducing noise on delicate furniture.
The semi-transparent finish allows discreet visual integration with different colours and finishes of furniture, without compromising strength or durability.
It is ideal for precision carpentry, kitchen, bathroom or bedroom furniture, and especially useful on furniture with doors that require additional protection on their closure to prevent wear or direct impact.
The following video shows how you can easily to disassemble the Vertex drawer.
The triangular design of the fastener allows secure mounting at the corners of skirtings, providing greater structural rigidity in corner areas. Its geometry is optimised for angled fixings, maximising strength and reducing torsional stresses.
The fastener is installed by means of a hole through the centre of one of its faces from side to side. The piece is inserted into the plinth by means of pressure or screws, using the through hole to attach it to the frame or base of the furniture.
The internal steel structure provides mechanical strength, while the white plastic coating prevents friction noise and enhances the aesthetics of the finish. This combination ensures durability without compromising the visual appearance.
It is especially recommended for fixing skirting boards in modular kitchens, bathroom furniture or cabinet systems that require a discreet and firm solution in corners or corners. Its pre-assembled design makes it ideal for quick assembly on production lines.
The product is delivered in packaging of 1000 units, which makes it highly efficient for automated assembly lines or large installations. This volume minimises logistical disruptions and optimises installation costs per unit.
The following video shows how you can easily assemble the oven grille.
Yes, board size are the same for both drawers only the height of the back board changes in the 93mm-high version.
Yes, the railings are the same for both drawers.
The RAL code of the white finish of the profiles system Gola is approximately 9003.The RAL code of the anthracite grey finish of the the profiles system Gola is approximately 7043.The RAL code of the black finish is approximately 9011.
The following video shows how you can easily assemble the profile system Gola.
In order to install the Gola profiles on a unit it is recommended to have gap measurements for being able to open the drawer or the door. These measurements are for guidance purposes and may vary depending on the overlaps.For an upper Gola profile it is recommended to have a 37 mm gap, and for a central Gola profile a 40 mm gap is recommended. The image shows a vertical view of the side of the unit.
The Gola system joining accessories are created using plastic (grey or white finish), and also, the accessories that are positioned on corners or corner edges require the profile to have a mitre joint.On the contrary, the straight cut accessories are created from matt silver anodized aluminium, and also, with all of them the profile only needs a straight cut, therefore preparation is easier.
Household appliances that can be integrated are completely compatible with the Gola profile system (with or without bumper). Thanks to that compatibility, household appliances remain hidden, thus adding a sense of continuity to kitchen furniture.In order to facilitate the work of manufacturers and assemblers, it is only necessary to bear in mind that the sum of the height along with the base, needs to be greater than the height of the household appliance along with the upper Gola profile that is used. Also, the attached document shows details with practical examples.
The following video shows how you can easily assemble the Gola profile for ovens.
The RAL code of the anthracite grey finish of the sides of the Vertex drawer is approximately 7043.
The RAL code of the grey finish of the sides of the Vertex drawer is approximately 7045.
The RAL code of the white finish of the sides of the Vertex drawer is approximately 9003.
For proper installation, this nut requires a 10 mm diameter hole. The knurled design on the outside of the nut improves the grip once it has been pressed in.
The recommended minimum depth is 5.7 mm and the maximum depth is 6.95 mm, thus allowing a correct insertion of the nut without damaging the board material.
This nut is compatible with screws, bolts or studs with metric M6 thread. Its internal thread must match the metric of the component to be fastened.
It is made of high-strength, durable technical plastic with a semi-transparent finish for discreet and secure installation.
The M6 nut connection system is available in packs of 2,500 pieces, ideal for series production or professional furniture assembly.
This coupling is installed by being pressed directly into the wood by machining. Installation is simple and requires no screws, as its shape is optimised for a firm press fit.
It is made of high-strength plastic, ensuring durability and a long service life. The white finish provides a clean, unobtrusive appearance, ideal for applications where aesthetics are also important.
This component is designed to generate hidden joints in wooden boards at 90°, making it ideal for the assembly of furniture with joints that are not visible from the outside, which improves the final appearance of the furniture.
The product is supplied in packs of 2500 units, which makes it particularly suitable for industrial production, series assembly or large-volume contract projects.
The H12 mm Block System allows fast, tool-free fastening, optimising assembly times and reducing the use of visible screws. Its design also minimises the risk of misalignment over time.
The following video shows how the sliding door system for wardrobes is assembled.
Each set of straight square tube brackets has a maximum load capacity of 10 kg per pair.
It is recommended to fix a wooden board 600 mm long by 200 mm deep to ensure stability and functionality.
Unlike the triangular bracket which maximises load bearing and stability, the straight square tube bracket offers a more modern linear aesthetic, ideal for decorative or medium duty shelving.
Includes screws and plugs for fixing the bracket to the shelf and wall.
Although it has a lower load-bearing capacity than the triangular version, it is designed for both decorative and functional purposes in everyday rooms.
The Supra trolley has optimised dimensions: height 487 mm, width 245 mm and depth 470 mm. It is compatible with 16, 18 and 19 mm thick boards.
It is installed directly on the base of the module by means of total extraction guides and cushioned closing system. The kit includes a basket with frame, bread bag, set of guides and mounting screws.
The system is adjustable in three axes: depth (±1.5 mm), horizontal (±2.25 mm) and height (±7.5 mm), facilitating precise installation in different configurations.
It has a load capacity of up to 25 kg, suitable for storing food, kitchen utensils and other items safely and efficiently.
It is made of steel with a chrome finish, which gives it strength, durability and a professional finish for kitchen base units.
The following video shows how you can easily install the Zero system.
The profile is designed to horizontally join each side of the base unit, providing a solid and stable joint. It is especially useful for reinforcing modules that house ovens or sinks, preventing unwanted movement.
It should be fixed to the top of the module, taking up as little space as possible. It is pressed into place with the connecting fitting and then screwed in place with Euro flat head or self-tapping screws Ø4.
Yes, the profile is supplied in a length of 2350 mm and can easily be cut to the required project size with a straight cut.
It is made of aluminium with a matt anodised finish for corrosion resistance and uniform aesthetics, ideal for high quality kitchens.
Yes, installation must be carried out in conjunction with the compatible connecting fittings, available in a press-fit or screw-fit version, ensuring maximum module stability.
It is designed to fit into standard 600 mm wide kitchen units, allowing precise integration into base units or oven columns.
The slats are made of extruded aluminium, which guarantees excellent mechanical strength, lightness and corrosion resistance, ideal for high temperature environments.
The mounting is carried out by means of 2 lateral brackets included, which allow an easy mounting without special tools, only with a conventional screwdriver.
Yes, the system allows quick assembly and disassembly of the slats, facilitating maintenance without the need to remove the entire structure of the furniture.
Its main function is to assemble the module by horizontally joining the sides, providing a strong and resistant fit that prevents displacement, especially in modules for sinks or areas with an oven.
Installation is by direct screwing using the included accessories (brackets, screws Ø3.5x25 mm and Ø4x20 mm), ensuring a quick and stable connection between the sides of the module.
Yes, both the four 1157 mm cross-member profiles and the bumper can be easily cut to the desired length by means of a straight cut, allowing precise customisation of the assembly.
The crossbar profile is made of matt anodised aluminium, while the brackets and bumpers are made of grey plastic, ensuring corrosion resistance and a professional aesthetic finish.
It is ideal for mounting low modules that require maximum structural rigidity in areas of intensive use, such as under sinks or industrial kitchens, where it is crucial to avoid module movement.
The bracket has compact dimensions of 200 mm x 200 mm x 380 mm, allowing it to be easily installed inside cabinets, doors or walls, even in confined spaces.
It is designed to hold electric irons, ironing boards and auxiliary accessories, thanks to its upper metal basket and lower fastening hooks.
Yes, the kit includes mounting screws. Installation is simple and straightforward on the wall or inside the cabinet, without the need for special tools.
Yes, the lower hooks are designed to hold standard ironing boards, ensuring that they are securely fixed in place and prevent them from sliding out of place when the cabinet is opened.
The curved metal hooks secure the ironing board by the legs or base, preventing it from sliding or falling into the wardrobe.
This profile reinforces the door structure, preventing deformation and maintaining alignment, especially on large doors.
It is designed for doors with an exact thickness of 16 mm, ensuring a precise and secure fit.
It is primarily designed for hinged doors, but can be adapted to sliding doors if the structure allows it and the thickness is 16 mm.
Yes, as it is made of steel, it provides greater structural resistance, avoiding deformation of the door and absorbing impacts better.
They are made of white painted steel, which provides great resistance, durability and a neutral aesthetic to adapt to different environments.
They must be screwed to the wall using the pre-drilled fixing points. The brackets are then easily slotted into the profile grooves.
They are compatible with single slotted shelf brackets with 50 mm pitch, designed to support wooden or glass shelves.
They are ideal for wardrobes, dressing rooms, laundry rooms, offices and shops, where a modular and adjustable shelving system is required.
It is recommended to use 6 mm diameter screws with dowels suitable for the type of wall to ensure a secure fixing.
They are compatible with 4 mm glass and 10 to 11 mm thick boards, ensuring a firm and stable installation.
The carriages are fitted to the top and bottom of the door using the hardware included in the kit.
In the commonly used door thicknesses of 40 mm and 45 mm, the clearance between the door and the wall is 14.8 mm and 12.3 mm respectively.
It is recommended to use a screwdriver and drill to fix the screws in position.
No, this kit does not include a brake or damping system. If soft closing is required, it is necessary to complement it with a Space+ compatible damping system.
Installation is done by screwing the bracket to the side of the cabinet.
It is made of zamak with a nickel-plated finish, which makes it highly resistant and durable.
There is no mention of screws being included, so it is recommended that screws suitable for the wood or installation surface be used.
Each package contains 1 side support. There are also options to buy in batches of 500 units.
No, the bracket is specifically designed for 30x15 mm oval bars, so it is not compatible with round bars or other dimensions.
A minimum depth of 250 mm is recommended, ensuring that the bar does not interfere with interior storage.
No, this bracket is designed for screw mounting on wood, MDF or melamine. For metal surfaces, specific fixings would be required.
Yes, it is recommended that the bracket be pre-milled to a depth of 3 mm to ensure that the bracket is correctly embedded in the side surface of the enclosure.
It has a length of 2,355 mm, with a cross-section of 20 mm high and 19 mm wide.
It is made of stainless steel, with a painted aluminium finish that mimics anodising for a sleek appearance and durability.
It is compatible with doors with a minimum thickness of 16 mm.
It is held in place by a 15 mm vertical flange, with a Ø6.5 mm hole in the 20 mm longitudinal section to facilitate mounting.
Supplied in kits of 10 units, ready for installation.
They are available in three lengths: 951 mm, 2064 mm and 2229 mm.
They are made of steel with a white painted finish, which guarantees resistance and neutral aesthetics for different applications.
These are double slotted rack profiles with a 32 mm pitch, designed for use with Jagmet shelf brackets to allow the installation of wooden or glass shelves.
Each batch contains 10 profiles ready for installation.
They are ideal for wardrobes, dressing rooms, pantries and laundry rooms, allowing the creation of modular shelves with height adjustment.
Installation requires a minimum internal cabinet depth of 430 mm to ensure full gliding of the system without interference.
This accessory is designed to support the usual weight of several clothes hangers, thanks to its aluminium structure. It is recommended not to exceed a distributed load of 12-15 kg in order to preserve the proper functioning of the extraction system.
The hanger is supplied with self-tapping screws suitable for melamine or wood boards. Mounting is carried out laterally to the sides of the cabinet, using 4 screws per unit.
Yes, although it is designed for wardrobe interiors, it can also be installed in open structures or walk-in closets without doors as long as the minimum required depth is respected.
The RAL code of the anthracite grey finish of the sides of the Concept drawer is approximately 7043.
The RAL code of the white finish of the sides of the Concept drawer is approximately 9003.
No, the hanger has a fixed length of 350 mm. For narrower modules, it is recommended to check the available space beforehand or consult specific models with adjustable measurements.
The thickness of the board that the sides of these modules can have is from 16 mm to 19 mm, as the luminaire includes lateral supports that adapt to the desired size.
This kit is designed to install a Luxe type hanging bar on the Zero modular profile. It is fixed by means of a lateral support, with a top cover that ensures stability and aesthetics.
The kit includes: 2 hanging rod holders, 1 set of tube fittings, 1 set of cover caps. This allows a stable fixation of the bar at two points and a professional finish.
No, the system is designed to fit without special tools. Installation is carried out on the Zero profile and does not require drilling or dismantling of components, which speeds up assembly on site or in the workshop.
Combined with a Luxe rail and the correctly anchored Zero system, it can support loads of up to 100 kg per module, ideal for wardrobes, dressing rooms and contract furniture.
The brackets are available in stone grey (RAL 7048) and textured black (RAL 9005). Made of zamak, they combine robustness with an unobtrusive appearance, integrating perfectly into contemporary or minimalist design furniture.
It is not recommended for use on tempered glass, as this material does not allow drilling and the installation of these hinges requires prior drilling at the base of the furniture.
These hinges are designed for lightweight glass doors from 4 to 6 mm thick, although the load capacity will depend on the size and weight of the glass used.
Yes, their steel construction with a metallic grey finish makes them resistant to moisture, which makes them suitable for furniture in humid environments such as bathrooms.
These hinges do not include a self-closing mechanism. If this function is required, it is necessary to supplement them with a damping or soft closing system.
Yes, the hinges allow the door to be removed by loosening the grub screws, facilitating maintenance or replacement of the glass without the need to completely remove the hinge.
For proper weight distribution and smooth movement, it is recommended to install hinges with a minimum gap of 250 mm to 300 mm, depending on the size and weight of the door.
The use of 3.5 x 16 mm or 4 x 16 mm flat head screws is recommended for optimum fastening in wood or MDF boards.
The 165° X95 hinge is designed to withstand loads of up to 5 kg per hinge, so it is recommended to use a minimum of two hinges for standard doors and to add more hinges for heavier doors.
Yes, the 165° X95 hinge can be combined with push-to-open systems and additional dampers, depending on the hinge mechanism and the supplements used.
No, the opening angle is fixed at 165°, but the hinge allows three-dimensional adjustment in height, depth and sideways for precise door adjustment.
The H56 siphon saver is distinguished by its reduced height of 56 mm and its thin-walled design, which allows for a more discreet and efficient integration into the interior of the drawer.
It is ideal for drawers with a reduced rear panel height of 56 mm and a panel thickness of 16 mm, and can be fitted in drawers with a minimum depth of 250 mm.
It is made of high quality plastic and is available in white, grey and anthracite grey finishes, which allows it to adapt to different styles of bathroom furniture.
It is installed by screwing it to the back of the drawer, without the need to machine the bottom. It is quick and easy to fix, without the need for specialised tools.
Its reduced height allows a better optimisation of the space in the drawer, maximising storage capacity without interfering with the structure of the furniture.
Yes, the drawer measurements, including its dimensions and machining, are fully compatible. The board cutting measurements, mounting dimensions and placement of the drawer in the module are exactly the same.This allows customers to mount 30 kg Concept slides and 50 kg slides on the same drawer.
The following video shows how you can easily assemble the Vantage-Q drawer.
In order to plan the design of a kitchen drawer unit with Vantage-Q drawers, we need to bear in mind several parameters, this work is made easier with a help table to configure those units.This calculation table makes it possible to calculate the position of the guides, depending on the dimensions of the unit and the number of drawers.Also, it makes it possible to choose different heights of drawer, consequently it calculates the height of the façade of each of them within the same unit.
In order to plan the design of a kitchen drawer unit with Vantage-Q drawers, we need to bear in mind several parameters, this work is made easier with a help table to configure those units.This calculation table makes it possible to calculate the position of the guides, depending on the dimensions of the unit and the number of drawers.Also, it makes it possible to choose different heights of drawer, consequently it calculates the height of the façade of each of them within the same unit.
We have different heights of sides and accessories that make it possible to create different types of drawers.You can design inner and exterior drawers, with a large capacity for saucepans, with rounded or square rails, with inside accessories and even glass sides.
