Technical assistance
We want to clear the main technical questions that may arise about the operation of our products and the steps necessary for their assembly.
Placard 74
The following video shows how the sliding door system for wardrobes is assembled.
There are two types of fittings that are used to fit glass doors on the Placard sliding system for wardrobes: - Plastic wedges. They are put into the handle profiles using pressure along with the glass, using four wedges on each side of the door and leaving the set fastened. It is also recommended to use the fitting profile (code. 4001621 / 7917121) for the rest of the handle profile and the crossbeam if there is one. - Screws. They are used to screw the upper and lower profiles of the door to the handles, to the runners and the rollers and to the Slowmove closing. These screws are a correct length in order not to damage the glass.
The following video shows how the sliding door system for wardrobes is assembled.
Yes, the current Ø50mm channel slider can be used with the new Placard 74 system but the gap for housing the upper and bottom rail needs to be increased from 74 to 77 mm in order to prevent the slider interfering with the inner divider or dividers.
The minimum recommended width that a door should have in order to mount soft Slowmove closing for Placard is 650 mm.
We can put a smooth closing device on the opening and a code 6102021 brake on the door closure. This will make sure the central door is not loose when closed or open.
The Slowmove soft closing system for Placard can be assembled on 2-door and 3-door wardrobes: For 2-door wardrobes you can install Slowmove soft closing on the opening as well as the closing of all the doors. However, on 3-door wardrobes you can install Slowmove soft closing only on the outer door for opening. For closing, it can be installed on all of the doors (inside and outside) depending on the closing movement.
Yes, it is possible to put a brake on the central door of a 3 door Placard wardrobe. However, it is necessary to take into account the opening of the central door in order to put the brake in, as it is only possible to have the brake in one direction. In the following diagram you can see the position of the brakes on the rail depending on the opening direction of the sliding doors.
No, the clipping pressure is sufficient so as not to require the use of screws, just like with the other Hill 19, Vall 19 and Line 19 aluminium handle profiles for 19 mm thick boards.
No, it is only compatible for the Placard 81 system.
The Wave 16 and Wave 16 E handle profiles for creating sliding doors have the same design and the same geometry for 16 mm thick board. The difference is that the Wave 16 E handle profile has a reduced thickness and is therefore more cost-effective.
These lower rails are used along with the Placard sliding door system and a fastening with a clip system.Both rails are very easy to assemble and more cost-effective thanks to the fact that a cover is not required to hide the fastening screws.The difference is that the first lower rail is available for boards of a 10mm, 16mm and 18mm thickness, and the second rail is designed for easy flush mounting on the edge of the furniture for 10 mm and 16 mm thick board.
The following video shows how the sliding door system for wardrobes is assembled.
Placard 81 soft closing set for one sliding door
Set of fittings Placard with Ø50 wheel for 1 door for sliding 70kg for soft-closing
Placard wheel set with wheel Ø50 for one sliding door up to 70kg with brake
Set of fittings for door with Slowmove (Soft-closing)
Set of fittings for sliding door of Groove
The RAL number of the white finish on the rails and handles of the Placard sliding door system is approximately 9003. The RAL code of the anthracite grey finish is approximately 7043. The RAL code of the black finish is approximately 9011.
Handle for wardrobe Sharp 19
Handle profile set Sharp 16, 18 and 19 for one sliding door
Classic Placard 74 upper track of Groove for sliding door
Handle profile set Wave 16 and 19 for one sliding door
Placard 74 lower track of Groove
Handle for wardrobe Sharp 16
Handle for wardrobe Style 16
Track set of Placard 74 of Groove
Track set of Placard 74 of groove with clip systems
Handle for wardrobe Wave 16
Handle for wardrobe Sharp 18
Placard 74 lower track of Groove with Clip systems for sliding door
Handle for wardrobe Wave 19
Crossbeams Placard U19x14
Sliding system for wardrobe 2 bottom sliding doors Placard 74 with Wave profiles and soft closing
Crossbeams Placard H19x12/22
Crossbeams Placard H16x18
Crossbeams Placard U16x14
Handle for wardrobe Style 10
Profile cover Placard of Groove for sliding door
Upper track for Slowmove
Classic Placard upper tracks and Placard of Groove for sliding door
Handle for wardrobe Wave 16
Crossbeams Placard U10x16
Handle for wardrobe Sharp 16
Placard lower track of Groove with Clip systems
Placard lower track of Groove for sliding door
Track set of Placard of Groove
Handle profile set Style 10 for one sliding door
Handle profile set Wave 16 for one sliding door
Upper track for Slowmove
Handle for wardrobe Hill 19 handle
Placard lower track of Groove for sliding door
The following video shows how the sliding door system for wardrobes is assembled.
The following video shows how the sliding door system for wardrobes is assembled.
Placard 81 soft closing set for one sliding door
Set of fittings Placard with Ø50 wheel for 1 door for sliding 70kg for soft-closing
Placard wheel set with wheel Ø50 for one sliding door up to 70kg with brake
Set of fittings for door with Slowmove (Soft-closing)
Set of fittings for sliding door of Groove
