The eccentric adjustment allows precise adjustments to be made to the door position, ensuring exact alignment with the furniture. This is essential for furniture where tolerances must be kept to a minimum.

The snap-in installation system with integrated ramps eliminates the need for additional screws, facilitating fast and secure assembly. This simplifies the installer's work and ensures a firm hold.

The 10x11 mm diameter ensures compatibility with standard bore holes and a stable connection to the furniture board, providing suitable support for X91/X92 hinges.

This supplement is ideal for furniture such as kitchen and bathroom cabinets, where a precise fit and sturdy mounting is required on doors with high daily use.

The nickel-plated finish not only enhances the aesthetics of the insert, but also protects it against corrosion, increasing its lifespan and making it easier to clean in wet or high traffic environments.

The following video shows how you can easily assemble the Ultrabox drawer.

The RAL code of the white finish of the sides of the Ultrabox kitchen drawer is approximately 9001.The RAL code of the aluminium finish of the sides of the Ultrabox kitchen drawer is approximately 9022.

We have a table for calculating the weight of a door, which is necessary to know when choosing guy ropes and measurements.Depending on the material of the door, as well as its dimensions, the result will be the weight of the door (kg) that you can use to calculate to the necessary strength of the measure (Kg x cm).

The 165° opening allows full access to the cabinet, improving functionality in applications where it is necessary to maximise space, such as corner cabinets or large storage cabinets.

The joint use of hinges and shims ensures secure support, improves door alignment and facilitates installation, especially in projects requiring high precision and durability.

Precise installation requires drilling holes 35 mm in diameter and 3 to 7 mm deep in the cup, ensuring that the doors are between 14 and 26 mm thick, and using the included screws to securely attach the shims and hinges.

The depth adjustment allows fine adjustments to be made to the position of the doors, correcting misalignments and ensuring that closing is smooth and functional, even on furniture with uneven surfaces.

Nickel-plated steel not only protects against corrosion and wear, but also provides an aesthetic finish, essential for furniture in wet or heavy use environments such as kitchens and offices.

The following video shows how to assemble runners for Silver drawer.

The following video shows how to adjust runners for Silver drawer.

Yes, the drawer measures are the same in the Silver and Slippe with partial and/or total extension with clips.

No, the drawer measures are different between.

The following video shows how you can easily assemble the Miniwinch system.

Maximum load capacity: Silver slides have a load capacity of up to 30 kg, which makes them ideal for domestic drawers with a considerable load.

Available adjustments: The guides allow adjustment in three directions: vertical (+3 mm), horizontal (+1.5 mm) and in depth (+3 mm), facilitating precise installation and a perfect fit.

Smooth closing: The self-closing system and the damping piston integrated in both slides prevent sudden shocks, prolonging the life of the drawer and offering a silent and smooth closing.

Depth compatibility: These slides are available in a variety of sizes, including depths of 290, 340, 390, 440, 490, 540 and 590 mm, adapting to different design needs.

Durability of design: They are made of zinc-plated steel, which ensures corrosion resistance and high durability, even under intensive use.

The Miniwinch folding door system can be installed in both wooden and aluminium doors.You only need to consider that it needs a door with A+10 where A is the side thickness of the furniture.For example, if the side thickness of the furniture is 19 mm, the door will be fitted at 29 mm.If the aluminium profile is 45 mm wide, it can be fitted because it can go inside the profile.We can also use the Ankor hinge in this combination, because it can fit easily.

This drawer is compatible with modules that allow a depth of 450 mm and are suitable for 18 mm thick back and front panels.

The kit includes slides, side ribs, a set of front hooks for mounting the drawer and screws required for installation.

This product complies with quality standards such as CATAS and FCBA certifications, guaranteeing its durability and resistance for intensive daily use.

The synchronised full-extension system provides smooth and silent sliding, optimising access to the interior of the drawer by allowing the full capacity to be utilised.

The trim covers enhance the aesthetic design of the drawer by covering the fixings, offering a clean, modern finish that blends in perfectly with the furniture.

This plate is compatible with the drawers of the Vertex, Concept and Convex ranges.

Installation is simple, as the plate is fitted to the side of the drawer by means of a clip located in the lower area, ensuring a firm and quick fixing.

Yes, the front of the plate can be screen-printed with a customised logo or design according to the customer's needs.

The plate is made of polypropylene with a finish available in various colours, such as white, grey and anthracite grey.

Yes, the plate can be installed on the left or right side of the drawer, as required.

The choice of a system for fold-down doors using a steel cable, like Microwinch or Miniwinch, depends on the height and weight of the door. To do so, you simply need to follow these simple steps:1. Check the height and the weight of the door. 2. Once you have obtained the values, look up the selection table. Depending on the weight of the door, you will be able to choose one fold-down system or another. Also, the table will indicate the number of systems needed for said door (x 1 or x2).

We have a table for calculating the pistons or dampners, where you can obtain a response with the furniture data.The choice will depend on the width and the height of the door, as well as the material it is manufactured out of, in addition to the stroke of the piston or damper itself.The result will be the number of pistons or dampners and the necessary strength of each one.

For the same force required in both folding and lift up doors, we recommend that you only use a single piston or damper in a door with a width of less than 450 mm, and that you use two pistons or dampers for a door that is wider than 450 mm.

The LED Lynx strip with a variable colour temperature has a controller that makes it possible to select a colour temperature of cool white, natural white or warm white, in a range between 3,000 Kelvin and 6,000 Kelvin.

The sensor uses infrared technology with a detection range of 5 cm, offering precise, non-contact activation.

It is ideal for applications in panels, headboards, kitchen furniture and different rooms in the home, thanks to its versatile and compact design.

Installation requires a Ø8 mm drill hole in the surface of the material. Includes a 2.5 m cable and a 6-input MiniLED distributor for easy mounting.

Supports 12V DC and 24V DC voltages, with a maximum power of 36W or 72W, depending on the connected LED system.

It is protected against electrical and electromagnetic interference, ensuring stable operation even in environments with high levels of electrical noise.

The I-connector is specifically designed to join 24V DC Pyxis LED luminaires, facilitating installation in linear configurations.

It allows the creation of longer luminaires by making use of surplus lengths of up to 5 metres.

Its self-sealing design and metal connectors ensure a solid and stable connection, preventing slippage within the profile and guaranteeing the passage of current from one luminaire to another.

It is made of transparent plastic and metal connectors. The transparent plastic maximises the luminous flux at the junction, while the metal connectors ensure efficient current transmission.

No, its transparent plastic construction means that the passage of light at the joints is not affected, guaranteeing uniform illumination.

The L connector is ideal for applications that require creating 90° angled junctions with the Pyxis 24V DC LED luminaire, perfect for perimeter lighting or corner designs.

It is necessary to cut the profiles at 45° mitres to ensure a perfect fit at 90° joints.

Allows luminaires up to 5 metres in length to be connected, optimising installation in angled designs.

It is made of transparent plastic with metal connectors. The transparent plastic optimises the passage of light, while the metal connectors ensure efficient current transmission.

No, the transparent design of the connector allows a uniform luminous flux to be maintained at the corner joints, maximising aesthetics and functionality.

The Placard U10x16 crossbar is used to provide greater stability and structural reinforcement to sliding door systems, allowing for smooth and safe sliding.

The crossbar has a length of 2.35 m, a profile of 10x16 mm and a thickness of 1.5 mm.

It is made of matt anodised or painted aluminium (black or white), guaranteeing resistance to wear and tear and a high quality finish.

Yes, the crossbar is compatible with Placard sliding door systems and other similar models using this type of reinforcement.

Yes, the transom can be cut with standard tools to fit the specific dimensions of the cabinet or door.

The system supports folding doors with loads of 20 kg and 25 kg per leaf. Compatible heights range from 1200 mm to 2700 mm, with panel thicknesses between 18 mm and 26 mm.

Yes, to be combined with the basic hardware kit, slide rails, vertical profile and, optionally, reinforcement profiles and centring strips.

No, the system uses a push-to-open mechanism, eliminating the need for handles. Opening is assisted and door adjustment is intuitive and accessible.

It includes pre-assembled components that speed up assembly, allowing for quick and precise installation. In addition, the system is designed to conceal the doors in the side of the cabinet or between walls.

Made of steel, aluminium and plastic, the system offers high strength, durability and a modern finish. Its design optimises the use of space while maintaining a clean aesthetic.

Kit includes: 2 side metal ribs and mounting hardware. It is designed for easy integration with Simplex drawer systems.

The ribs are made of high-strength steel, available in white painted and anthracite grey finishes. Both finishes guarantee durability, corrosion resistance and aesthetic design.

The system is designed for drawers with a height of 86 mm and multiple depths: 290 mm, 340 mm, 400 mm and 440 mm. Compatible with full-extension slides and Simplex soft close systems.

Yes, installation is quick and easy. No special tools are required. Just assemble the ribs with the slides and fix them to the front of the drawer with the included screws.

The system supports up to 35 kg per drawer, ideal for residential and commercial applications.

Yes, just press the MATCH button on each controller and the 1,2,3 or 4 buttons on the controller to link it.

The Optima Vantage cutlery tray is compatible with standard width module drawers of 600 mm and 900 mm, with a depth of 500 mm and 16 mm thick board.

Yes, the Optima Vantage cutlery tray can be easily trimmed to fit the specific dimensions of the drawer, providing a customised installation.

It is made of high-quality, hard-wearing grey plastic, designed for durability and ease of cleaning.

Yes, the material used in the cutlery tray is resistant to moisture and daily wear and tear, ensuring longevity in kitchen environments.

The cutlery tray design includes a precise fit to keep it stable inside the drawer, preventing movement during use.

The RAL number of the white finish on the rails and handles of the Placard sliding door system is approximately 9003. The RAL code of the anthracite grey finish is approximately 7043. The RAL code of the black finish is approximately 9011.

The Neco rail can be installed on melamine, MDF or chipboard surfaces. The use of structural adhesive or appropriate screws is recommended depending on the type of support. The base of the rail allows a flush fit to the bottom of the module, optimising the visual finish and the stability of the assembly.

This track is specifically designed for the bottom guide sliding door system and is compatible with the Emuca Placard model door system. It must be used in conjunction with a top profile and bottom wheels that fit into the 15mm wide channel of the track.

Combined with the Placard system components, this rail can support a load of up to approximately 50 kg per door, provided that the recommendations for mounting, wheel centring and module levelling are observed.

The rail is made of matt anodised aluminium, which provides excellent resistance to corrosion, scratching and frictional wear. This makes it a durable choice for heavy duty applications in both domestic and contract environments.

Each package includes 8 units of rails, each with a length of 2.35 metres. This makes it easy to optimise cutting and assembly in large volume projects or industrial installations.

The Ledown leveller offers an adjustment capacity of up to 25 mm by means of an Allen key no. 4. This allows it to absorb manufacturing tolerances or floor irregularities, without altering the external aesthetics of the module thanks to its completely concealed installation.

Cylindrical machining with a diameter of Ø12 mm and a depth of at least 16 mm is recommended. The body of the levelling device is pressed into the side and rests on the lower base of the side, which ensures a direct load transmission.

Adjustment is made from the underside of the furniture using a standard Allen key no. 4. This system facilitates fine adjustment once the furniture has been installed, without the need to remove plinths or front panels.

Yes, its design allows adjustment from inside the plinth by means of a through hole or side recess. It is especially useful in kitchens or bathroom furniture where total concealment and accessibility from service areas is required.

Each leveller supports up to 250 kg. It is made of steel and zinc plated zamak, which ensures mechanical strength, dimensional stability and protection against corrosion in wet or exposed environments.

The Pozidriv design provides a better engagement between the screwdriver and the screw, reducing the risk of slippage or wear during installation. This improves accuracy and safety in repetitive assembly or with power tools.

Only a Pozidriv 2 compatible screwdriver is required for secure installation. No pre-drilling is necessary, as they are designed for direct fixing on wooden parts with a 5 mm diameter pre-drilled hole.

These screws are suitable for connecting furniture fittings, especially in structures where a firm and stable fixing is required without the need for nuts or inserts. They are ideal for quick pre-assembly on production lines.

The screws have a diameter of 6.2 mm and a total length of 13 mm, offering an optimum balance between penetration and strength for general purpose use in wood or chipboard up to 19 mm thick.

The zinc-plated finish provides additional resistance against corrosion and rust, which is essential in humid environments or to extend the life of hardware in assemblies exposed to variable conditions.

This system is designed for boards at least 16 mm thick, providing a secure fixing for shelves in cupboards, kitchens or general furniture.

The couplings require Ø20 mm holes with a minimum depth of 12.5 mm, ensuring a precise fit without compromising the structural integrity of the board.

The hitch is made of nickel-plated zamak, while the bolt is made of turned steel with a zinc-plated finish, a combination that ensures rust resistance and long-term durability.

The kit includes bolts of 8 mm and 11 mm in length and 6 mm or 8 mm in diameter, allowing for different mounting configurations depending on the design of the furniture or shelf.

The set contains 20 couplings and 20 bolts, presented in a format ideal for professional installations or mass production, with a nickel-plated finish for uniform aesthetics and corrosion protection.

The RAL code of the white finish of the Optima cutlery holder is approximately 9003. The RAL code of the grey finish of the Optima cutlery holder is approximately 7001. The RAL code of the anthracite grey finish of the Optima cutlery holder is approximately 7043.

The Optima cutlery holder has a wide range of models and sizes. The cutlery holder intended for the Vantage-Q drawer is not compatible with the Slim drawer. as a a cutlery holder model exists for the Slim drawer.Both models have the same depth but not the same width, specifically, the cutlery holders for the Slim drawer are 6 mm narrower than the cutlery holders for the Vantage-Q drawer.

Yes, the Vantage-Q waste container is compatible with the 18 and 19 mm Slim drawer.

The expansion tip has been designed to be used exclusively with the Wedge Coupling Brackets Ø19 and the Wedge Coupling Ø19 of the shelf connection system, ensuring precise and efficient integration.

It has a diameter of 3.5 mm and a maximum length of 25 mm. These dimensions allow a firm fastening that withstands tensile loads thanks to its all-steel construction, guaranteeing secure fastening.

The zinc plated finish provides additional protection against rust and corrosion, which is essential to ensure the durability of the component in high humidity or prolonged exposure environments.

No, it is installed by means of a pin in the Ø19 wedge system, without the need for special machining, which optimises time and costs for in-line assembly processes or customised projects.

The expansion tip is supplied in boxes of 10,000 units, ideal for mass production environments where a high volume of stock is required, thus reducing the frequency of replenishment and facilitating storage.

The Ø19 plastic tip stands out for its flexibility and light weight, which facilitates installation without heavy tools. In addition, its transparent design offers a cleaner and more discreet aesthetic for applications in visible furniture such as kitchens or bathrooms.

Thanks to its expandable design, the Ø19 plastic tip provides a firm and secure coupling with different board thicknesses, provided it is used in conjunction with the Ø19 coupling and wedge system. Its elasticity allows it to adapt precisely.

Installation requires a cylindrical housing to allow the plastic tip to be inserted into the holder. The rounded shape facilitates manual or automated assembly on production lines.

Yes, this tip has been specifically designed to work with the Ø19 Wedge Coupling and Coupling Brackets. This ensures full compatibility in installations that combine metal and plastic parts in the same structure.

This product is delivered in strings of 10,000 units, ideal for automated assembly lines and large-scale assembly processes. The strip format improves logistical efficiency and handling during installation.

The profile is designed to horizontally join each side of the base unit, providing a solid and stable joint. It is especially useful for reinforcing modules that house ovens or sinks, preventing unwanted movement.

It should be fixed to the top of the module, taking up as little space as possible. It is pressed into place with the connecting fitting and then screwed in place with Euro flat head or self-tapping screws Ø4.

Yes, the profile is supplied in a length of 2350 mm and can easily be cut to the required project size with a straight cut.

It is made of aluminium with a matt anodised finish for corrosion resistance and uniform aesthetics, ideal for high quality kitchens.

Yes, installation must be carried out in conjunction with the compatible connecting fittings, available in a press-fit or screw-fit version, ensuring maximum module stability.

It is compatible with 19 to 20 mm thick doors.

The profile is fixed by means of a 3.7 mm centre groove, which makes it easy to mount and align on the door.

The profile has a width of 47 mm in the vertical part and 25.7 mm in the horizontal part, which allows an aesthetic and functional integration into the furniture design.

Yes, it can be combined with other accessories and profiles from the Free range to achieve a uniform and functional wardrobe design.

No, the packaging includes only the profiles.

It is compatible with Jagmet rack profiles: Single groove with 50 mm pitch Double groove with 32 mm pitch

Each basket measures 789 x 354 x 116 mm, giving a capacity of approximately 32 litres per unit.

All components are made of white lacquered steel, which gives the system high strength and a uniform aesthetic finish for interior furnishings.

This kit is designed to create shelves with removable wire baskets, ideal for inside wardrobes, dressing rooms, laundry rooms or pantries.

The set contains: 2 removable wire baskets 2 sets of brackets (one for each basket, with left and right brackets)

The set contains: 2 removable wire baskets 2 sets of brackets (one for each basket, with left and right brackets)

It is compatible with Jagmet rack profiles: Single groove with 50 mm pitch Double groove with 32 mm pitch

Each basket measures 789 x 354 x 116 mm, giving a capacity of approximately 32 litres per unit.

All components are made of white lacquered steel, which gives the system high strength and a uniform aesthetic finish for interior furnishings.

This kit is designed to create shelves with removable wire baskets, ideal for inside wardrobes, dressing rooms, laundry rooms or pantries.

Each bar supports a maximum load of 10 kg, according to product specifications.

Each bar has dimensions of Ø27 x 815 mm, which makes it suitable for interior cabinet spaces.

It is compatible with Jagmet wire baskets and their shelf supports, integrating as part of the same modular system.

The components are made of white lacquered steel, offering high resistance and uniform aesthetics for the interior of wardrobes, dressing rooms or pantries.

The kit contains: 2 x 815 mm bars 2 sets of brackets (right and left) 2 sets of end caps

Each hanger measures 321 mm in length in extended position, allowing several hangers to be hung without interfering with each other.

It is suitable for space-saving areas such as walk-in wardrobes, wardrobes or laundry rooms, where a temporary, collapsible storage solution is needed.

Including 4 screws Ø4.8x42 mm and plugs Ø8x40 mm, suitable for fixing to solid walls such as brick, concrete or solid partition walls.

Installation is carried out using the screws and plugs included. No additional accessories are required, and it is fixed directly to the wall.

The design includes holes for inserting the hangers, which allows the hanger to be swung towards the wall without the hangers sliding or falling off during movement.

The supplements or bases that are used along with the hinges have two holes for fastening to the furniture and a third hole for increasing the resistance of the hinge/supplement joint. It is especially designed for facilities that require more resistance such as on doors with pistons.

The following video shows how such a system is easily assembled:

It allows the Zero profile to be fixed to the floor and ceiling, and is used to form a continuous vertical structure in installations without wall fixing.

The leveller allows a height adjustment of 10 mm, which facilitates precise adjustment to the ceiling or floor.

It is made of zamak with a textured stone grey painted finish (RAL 7048) and grey plastic, providing robustness and uniform aesthetics.

Includes: 1 leveller 2 screws Ø4x30 2 plugs Ø6x30 1 cover 1 Allen key 1 circular felt for the base

It is ideal for free-standing Zero structures with floor-ceiling fixing, especially as room dividers in homes, offices or shops.

The following video shows how to assemble such a box in a simple way:

This magnetic lock has a holding force of 3.2 kg, ensuring that the door remains securely closed.

The magnet is screwed to the surface of the cabinet. The magnet is placed inside the cabinet and the metal plate on the door.

It is ideal for furniture with hinged doors in kitchens, bathrooms, wardrobes and other interior furniture where a secure and discreet closure is required.

It is made of steel and plastic with a white finish, which gives it strength and aesthetic integration into different types of furniture.

Yes, each lot includes 20 magnetic closures and 20 metal plates for installation.

The following video shows how such a system is easily assembled:

The following video shows how such a system is easily assembled:

This hinge is specifically designed for glass doors with a thickness between 4 and 6 mm, providing a firm and stable hold.

To install the bushing, it is necessary to drill a 9 mm hole in the base of the furniture where it will be placed. Then, the hinge is fixed by pressing the glass with screws, ensuring that it does not move.

It is made of stainless steel with an aluminium painted finish, giving it greater resistance to corrosion and an aesthetically pleasing design.

Each package contains 200 pieces, divided into 100 hinges for the right side and 100 for the left side.

It does not require intensive maintenance, but it is recommended to clean periodically with a dry cloth or a specific metal cleaner to maintain its appearance and functionality.

The X12 hinge allows precise adjustments by eccentric adjustment: Height: ±2 mm Depth: ±2 mm Side: ±1 mm This guarantees perfect alignment of the door even in installations with small variations.

For fixing the X12 hinge, screws with a diameter of 3.5 to 4 mm and a length of 12 to 16 mm are recommended, depending on the furniture material.

A properly installed X12 hinge can support up to 8 kg per unit. It is recommended to install at least two hinges on doors up to 600 mm high and three or more on larger doors.

This hinge is designed for doors from 12 to 18 mm thick. If the door is thicker than this, the hinge cup may not align properly and affect the opening and closing of the door.

No, the X12 hinge is designed exclusively for wooden doors or derivatives. For glass, specific hinges with pressure or adhesive fixing are required.

The X12 elbow hinge is designed for partially overlapping doors, which means that the door covers only part of the side of the furniture. In contrast, the X12 straight hinge is used for fully overlapping doors.

The X12 elbow hinge has a 26 mm diameter cup and allows a 95° opening angle, which facilitates easy access to the inside of the furniture.

No, the X12 elbow hinge is specifically designed for doors 12 to 18 mm thick. If the door is thinner or thicker, the installation may not be suitable and may affect alignment and locking.

Screws with a diameter of 3.5 to 4 mm and a length of 12 to 16 mm are recommended, depending on the furniture material.

The three-dimensional adjustment allows the following settings: Height: ±2 mm Depth: ±2 mm Sideways: ±1 mm These adjustments help to correct any misalignment after assembly.

The X12 super elbow hinge is designed for furniture where the door must fully retract into the furniture frame. In contrast, the X12 elbow hinge allows the door to partially overlap the side of the furniture.

The X12 super elbow hinge has a 26 mm diameter cup and an opening angle of 95°, providing convenient access to the furniture.

Snap-on (clip): SKU Model 1271607, facilitates quick installation without the need for additional tools. Screw-on: SKU Model 1270507, for traditional screw installation.

Yes, this hinge allows three-dimensional adjustment, which facilitates perfect alignment of the door: Height: ±2 mm Depth: ±2 mm Side: ±1 mm

It is recommended to install it on doors with a thickness between 12 and 18 mm, as a smaller or larger thickness could affect its correct functioning.

The X12 supplement allows the height of the X12 hinge to be adjusted to correct the alignment of the door. It is particularly useful when the door is not perfectly aligned with the furniture after initial installation.

This model is available in two versions: Height -2 mm (SKU 1270607): Reduces the hinge position by 2 mm. Height 0 mm (SKU 1270707): Maintains the standard position without changing the height.

It is designed for use with X12 hinges that require a 26 mm diameter cup, ensuring accurate installation on wooden doors.

It is fixed to the furniture with screws. The X12 hinge is mounted on the supplement, adjusting the desired height. It allows small corrections to be made to the alignment of the door without dismantling the entire hinge.

It is made of steel with a nickel-plated finish, which provides high corrosion resistance and increased durability in kitchen, office and home furniture.

The X12 Euro supplement is specifically designed for hinges with Euro system, which allows faster fastening by means of pre-installed screws and adjustment by means of eccentrics.

Height -2 mm (SKU 1270807): Reduces the height of the hinge by 2 mm. Height 0 mm (SKU 1270907): Maintains the standard height without modification.

This supplement is compatible with X12 hinges with Ø26 mm cup, used on wooden doors. Its adjustment system is ideal for hinges with Euro mounting, ensuring fast and accurate installation.

It is attached to the furniture using the integrated screws. The hinge is mounted directly on the supplement and is adjusted by means of the eccentric adjustment. Its mounting system facilitates adjustments without the need to dismantle the hinge.

It is constructed of steel with a nickel-plated finish, which provides high corrosion resistance and increased durability in kitchen, office and home furniture.

The supplement is designed to support the standard X12 hinge load, allowing an even distribution of the door weight. However, the final strength will depend on the type of material it is installed in and the number of hinges used.

This supplement is compatible with wooden doors between 12 and 18 mm thick, as it is specifically designed for use with Ø26 mm X12 cup hinges.

The height of the supplement affects the positioning of the hinge and the alignment of the door: Height -2 mm: Allows adjustments to correct minor door misalignments. Height 0 mm: Maintains standard alignment with no change in hinge position.

Not recommended, as it is specifically designed for the X12 hinge series with Ø26 mm cup. For compatibility with other hinges, it is best to consult the manufacturer's specifications.

The supplement allows for three-dimensional adjustment, which facilitates perfect alignment of the door through height, side and depth adjustments when used with compatible hinges.

The Ultrabox drawer consists of two steel side ribs and drop locking slides, which give it stability and strength. It is delivered with the hitch mounted on the rib, facilitating installation.

Each drawer supports up to 25 kg load, making it ideal for kitchen, bathroom and office furniture applications where safe and sturdy storage is required.

The clamping system allows ±2 mm eccentric adjustment vertically, facilitating fine adjustments to ensure precise alignment and optimal closure.

No, the bottom of the drawer does not require machining, which simplifies the assembly process and reduces installation times.

Yes, this drawer is compatible with soft closing systems, although they are not included in the lot. For implementation, it would be necessary to purchase additional components compatible with the Ultrabox system.

What load capacity does the system support and how is it distributed?

What tools and machining are necessary for its installation?

Where is the hanger installed and what type of wall anchor is used?

How is the position of the module adjusted once it is hung?

What materials make up the kit and what advantages does it offer in demanding environments?

At Emuca, we make it easy for you. Here you can download this Excel file that will help you configure your drawer unit step by step. Simply enter the module measurements (height, thickness, overlap, etc.) and specify how many drawers you want. This file allows you to:

• Automatically calculate the machining dimensions of the drawer fronts (H1, H2, H3...) (mm).
• Determine the height of each drawer front (mm).
• And obtain the machining dimensions required to manufacture the drawer fronts (X, Y) (mm).

It also includes visual representations so you can check the result and avoid errors. Ideal for carpenters, designers or DIY enthusiasts who want a practical and accurate solution.

If a warning message appears when you open the Excel file, close the file. Right-click on the downloaded file and select Properties. At the bottom of the window, tick the box Unblock. Click Apply and then OK. You can now open the file.

The following video shows how you can easily assemble the Slim drawer.

The RAL code of the anthracite grey finish of the sides of the Slim kitchen, household and bathroom drawer is approximately 7043.The RAL code of the white finish of the sides of the Slim kitchen, household and bathroom drawer is approximately 9003. Although it is necessary to bear in mind that the white silk colour of said drawer is metallized and the RAL codes are for flat colours.

Yes, the bottom and the back of the Slim drawer have the same measurements for both the soft closing runners and the push runners.